Best solution to keep your engine in good shape

he crankcase and the part of the cylinder below the piston is used as a pump. The intake port is connected to the crankcase through a reed valve or a rotary disk valve driven by the engine. For each cylinder a transfer port connec

Best solution to keep your engine in good shape reduce smoke TVR

Crankcase scavenged

Crankcase scavenged
Diagram of a crankcase scavenged 2-stroke engine in operation

Some SI engines are crankcase scavenged and do not use poppet valves. Instead the crankcase and the part of the cylinder below the piston is used as a pump. The intake port is connected to the crankcase through a reed valve or a rotary disk valve driven by the engine. For each cylinder a transfer port connects in one end to the crankcase and in the other end to the cylinder wall. The exhaust port is connected directly to the cylinder wall. The transfer and exhaust port are opened and closed by the piston. The reed valve opens when the crankcase pressure is slightly below intake pressure, to let it be filled with a new charge; this happens when the piston is moving upwards. When the piston is moving downwards the pressure in the crankcase increases and the reed valve closes promptly, then the charge in the crankcase is compressed. When the piston is moving upwards, it uncovers the exhaust port and the transfer port and the higher pressure of the charge in the crankcase makes it enter the cylinder through the transfer port, blowing the exhaust gases. Lubrication is accomplished by adding 2-stroke oil to the fuel in small ratios. Petroil refers to the mix of gasoline with the aforesaid oil. This kind of 2-stroke engines has a lower efficiency than comparable 4-strokes engines and release a more polluting exhaust gases for the following conditions:

They use a total-loss lubrication system: all the lubricating oil is eventually burned along with the fuel.
There are conflicting requirements for scavenging: On one side, enough fresh charge needs to be introduced in each cycle to displace almost all the combustion gases but introducing too much of it means that a part of it gets in the exhaust.
They must use the transfer port(s) as a carefully designed and placed nozzle so that a gas current is created in a way that it sweeps the whole cylinder before reaching the exhaust port so as to expel the combustion gases, but minimize the amount of charge exhausted. 4-stroke engines have the benefit of forcibly expelling almost all of the combustion gases because during exhaust the combustion chamber is reduced to its minimum volume. In crankcase scavenged 2-stroke engines, exhaust and intake are performed mostly simultaneously and with the combustion chamber at its maximum volume.

The main advantage of 2-stroke engines of this type is mechanical simplicity and a higher power-to-weight ratio than their 4-stroke counterparts. Despite having twice as many power strokes per cycle, less than twice the power of a comparable 4-stroke engine is attainable in practice.

In the USA two stroke motorcycle and automobile engines were banned due to the pollution, although many thousands of lawn maintenance engines are in use.citation needed

Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine


Outlined car

One of the most common problems, which has to face many a owner of such a vehicle such as a car or a motorcycle, a scratch on the car paint. We can scratch the car in just a few moments, without using even this sharp tool. Many scratches formed, for example, the inability of parking or reversing. Unfortunately, many of them are also the result of actions of hooligans, we leave the car, for example, in the wrong neighborhood. How to deal with such a problem? Of course, in many cases it is necessary to visit the factory paint. In smaller straches it may be useful to also use, for example, with a special pen that allows at least a little to mask the resulting defects.


There are several possible ways

Classification

There are several possible ways to classify internal combustion engines.

Reciprocating:

By number of strokes

Two-stroke engine

Clerk Cycle 1879 6
Day Cycle

Four-stroke engine (Otto cycle)
Six-stroke engine

By type of ignition

Compression-ignition engine
Spark-ignition engine (commonly found as gasoline engines)

By mechanical/thermodynamical cycle (these 2 cycles do not encompass all reciprocating engines, and are infrequently used):

Atkinson cycle
Miller cycle

Rotary:

Wankel engine

Continuous combustion:

Gas turbine
Jet engine

Rocket engine
Ramjet

The following jet engine types are also gas turbines types:

Turbojet
Turbofan
Turboprop



Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine